نمایش نتایج جستجو برای
کلمات کلیدی: Milling
موارد یافت شده: 33
1 - On the milling and preheating on fabrication of NiTi produced by combustion synthesised NiTi (چکیده)2 - Milled Rice Quality Assessment (چکیده)
3 - Carburising behaviour of low carbon steel with nanocrystalline surface layer induced by ball milling (چکیده)
4 - Application of Taguchi Method Grey Analysis and ANOVA in Optimization of Titanium Alloys Milling (چکیده)
5 - The Effect of MWCNT on the Mechanical and Electrical Properties of HDPE/MWCNT Nanocomposite (چکیده)
6 - Formation of Nanocrystalline and Ultrafine-grained Structures in Disk-shaped Samples of Fe-0.15C and Interstitial-free (IF) Steels Produced by Ball Milling (چکیده)
7 - Effect of Mechanical Milling on the Thermal Behavior of Polyethylene Reinforcedwith Nano-sized Alumina (چکیده)
8 - Simulation of Serrated End Milling Using Solid Modeling Techniques (چکیده)
9 - EFFECT OF MECHANICAL ACTIVATION ON THE KINETICS OF LEACHINGOFCHALCOPYRITE IN THE FERRIC SULFATE MEDIA (چکیده)
10 - On the Dependence of Avrami Indexes of MDPE on Milling Time (چکیده)
11 - Prediction of Thread Milling Instantaneous Cutting Forces (چکیده)
12 - Effect of Milling Time and Clay Content on the Thermal Stability of Polyethylene-Clay Nanocomposite (چکیده)
13 - Geometric simulation of surface texture in low immersion side milling (چکیده)
14 - THE EFFECT OF GRINDING TIME ON THE SPECIFIC SURFACE AREA DURING INTENSIVE GRINDING OF MINERAL POWDERS (چکیده)
15 - EFFECTS OF HELIX ANGLE VARIATIONS ON STABILITY OF LOW IMMERSION MILLING (چکیده)
16 - Dynamic Force Model for 3- Axis Ball-End Milling of Sculptured Surfaces (چکیده)
17 - Investigating Stability Limits in High Speed Milling of Titanium Thin-Walled Parts (چکیده)
18 - Surface Integrity of Thin-Walled Titanium Parts Machined by Peripheral Milling (چکیده)
19 - Geometric Simulation of Ball-End Milling Operations (چکیده)
20 - Influence of Nano-Size Al2O3 Weight Percent on the Microstructure and Mechanical Properties of Al-Matrix Nanocomposite (چکیده)
21 - Development and verification of a mathematical model for variations of the specific surface area of mineral powders during intensive grinding (چکیده)
22 - Development of a mathematical expression for the variation of amorphization phenomenon during intensive milling of minerals (چکیده)
23 - On the role of nano-size SiC on lattice strain and grain size of Al/SiC nanocomposite (چکیده)
24 - Crystallinty behavior of MDPE-clay nanocomposites fabricated using ball milling method (چکیده)
25 - Synthesis of PE-Cu-C Nano-Crystalline Composite by Mechanochemical Technique (چکیده)
26 - ANTICIPATION OF STABILITY LIMITS FOR TWO DEGREE-OF -FREEDOM INTERRUPTED MILLING (چکیده)
27 - prediction of Al-B4C nanocomposite powder particle size distribution bu nueral network modeling (چکیده)
28 - Crystallinity Behavior of MDPE-Clay Nanocomposites Fabricated using Ball Milling Method (چکیده)
29 - The Effect of Milling Conditions on Morphology and Grain Size of Al/SiC Nanocomposite Powders Produced by Mechanical Alloying Method (چکیده)
30 - Synthesis of Al-Al2O3 Nano-Composite by Mechanical Alloying and Evaluation of the Effect of Ball Milling Time on the Microstructure and Mechanical Properties (چکیده)
31 - Geometric Simulatiin of Five - Axis Ball -End Milling (چکیده)
32 - Synthesis of Al-Al2O3 Nano-Composite by Mechanical Alloying and Evaluation of the Effect of Ball Milling Time on the Microstructure and Mechanical Properties (چکیده)
33 - Feed rate optimization for 3-axis ball-end milling of sculptured surfaces (چکیده)
